docs/source/sdr_guides/blade.rst

@@ -43,7 +43,13 @@ Limitations
 Set up instructions (Linux, Radioconda)
 ---------------------------
 
-Step 1: Install the base dependencies and drivers ('Easy method')
+Step 1: Activate your Radioconda environment.
+
+.. code-block:: bash
+
+    conda activate <your-env-name>
+
+Step 2: Install the base dependencies and drivers ('Easy method')
 
 .. code-block:: bash
 
@@ -53,13 +59,6 @@ Step 1: Install the base dependencies and drivers ('Easy method')
     sudo apt-get install libbladerf-dev
     sudo apt-get install bladerf-fpga-hostedxa4   # Necessary for installation of bladeRF 2.0 Micro A4.
 
-
-Step 2: Activate your Radioconda environment.
-
-.. code-block:: bash
-
-    conda activate <your-env-name>
-
 Step 3: Install a udev rule by creating a link into your radioconda installation.
 
 .. code-block:: bash

docs/source/sdr_guides/pluto.rst

@@ -52,7 +52,7 @@ Step 1: Activate your Radioconda environment.
 
     conda activate <your-env-name>
 
-Step 2: Install system dependancies
+Step 2: Install system dependancies.
 
 .. code-block:: bash
 

docs/source/sdr_guides/rtl.rst

@@ -1,93 +0,0 @@
-.. _rtl:
-
-RTL-SDR
-=======
-
-RTL-SDR (RTL2832U Software Defined Radio) is a low-cost USB dongle originally designed for digital TV reception
-that has been repurposed as a wideband software-defined radio. RTL-SDR devices are popular for hobbyist use due to
-their affordability and wide range of applications.
-
-The RTL-SDR is based on the Realtek RTL2832U chipset, which features direct sampling and demodulation of RF
-signals. These devices are commonly used for tasks such as listening to FM radio, monitoring aircraft traffic
-(ADS-B), receiving weather satellite images, and more.
-
-Supported Models
-----------------
-
-- **Generic RTL-SDR Dongle:** The most common variant, usually featuring an R820T or R820T2 tuner.
-- **RTL-SDR Blog V3:** An enhanced version with additional features like direct sampling mode and a bias tee for
-  powering external devices.
-
-Key Features
-------------
-
-- **Frequency Range:** Typically from 24 MHz to 1.7 GHz, depending on the tuner chip.
-- **Bandwidth:** Limited to about 2.4 MHz, making it suitable for narrowband applications.
-- **Connectivity:** USB 2.0 interface, plug-and-play on most platforms.
-- **Software Support:** Compatible with SDR software like SDR#, GQRX, and GNU Radio.
-
-Limitations
------------
-
-- Narrow bandwidth compared to more expensive SDRs, which may limit some applications.
-- Sensitivity and performance can vary depending on the specific model and components.
-- Requires external software for signal processing and analysis.
-
-Set up instructions (Linux, Radioconda)
----------------------------
-
-Step 1: Activate your Radioconda environment.
-
-.. code-block:: bash
-
-    conda activate <your-env-name>
-
-Step 2: Purge drivers.
-
-If you already have some other drivers installed, purge them from your system.
-
-.. code-block:: bash
-
-    sudo apt purge ^librtlsdr
-    sudo rm -rvf /usr/lib/librtlsdr* 
-    sudo rm -rvf /usr/include/rtl-sdr* 
-    sudo rm -rvf /usr/local/lib/librtlsdr* 
-    sudo rm -rvf /usr/local/include/rtl-sdr* 
-    sudo rm -rvf /usr/local/include/rtl_* 
-    sudo rm -rvf /usr/local/bin/rtl_*
-
-Step 3: Install RTL-SDR Blog drivers.
-
-.. code-block:: bash
-
-  sudo apt-get install libusb-1.0-0-dev git cmake pkg-config build-essential
-  git clone https://github.com/rtlsdrblog/rtl-sdr-blog
-  cd rtl-sdr-blog/
-  mkdir build
-  cd build
-  cmake ../ -DINSTALL_UDEV_RULES=ON
-  make
-  sudo make install
-  sudo cp ../rtl-sdr.rules /etc/udev/rules.d/
-  sudo ldconfig
-
-Step 4: Blacklist the DVB-T modules that would otherwise claim the device:
-
-.. code-block:: bash
-  
-  sudo ln -s $CONDA_PREFIX/etc/modprobe.d/rtl-sdr-blacklist.conf /etc/modprobe.d/radioconda-rtl-sdr-blacklist.conf
-  sudo modprobe -r $(cat $CONDA_PREFIX/etc/modprobe.d/rtl-sdr-blacklist.conf | sed -n -e 's/^blacklist //p')
-
-Step 5: Install a udev rule by creating a link into your radioconda installation.
-
-.. code-block:: bash
-
-  sudo ln -s $CONDA_PREFIX/lib/udev/rules.d/rtl-sdr.rules /etc/udev/rules.d/radioconda-rtl-sdr.rules
-  sudo udevadm control --reload
-  sudo udevadm trigger
-
-Further Information
--------------------
-
-- `Official Website <https://www.rtl-sdr.com/>`_
-- `RTL-SDR Quick Start Guide <https://www.rtl-sdr.com/rtl-sdr-quick-start-guide/>`_